CLEARANCE SALE- XLong Smooth Firestop Sleeve System- 1″ x 18″- Case of 75 – 50% off + FREE Shipping!

Price: $975.00
 
Unique SF1x18 Smooth Firestop Sleeve
Unique SF1x18 Smooth Firestop Sleeve

Unique SF1x18 Smooth Firestop Sleeve

 

 

 

 

HUGE CLEARANCE SALE! Get 50% off our overstocked specialty item, the XLong UNIQUE Smooth Firestop Sleeve System in a galvanized finish, 1″ in diameter x 18″ long. This product is being sold by the case, 75 units to the case @ $13/unit with FREE SHIPPING.  Our inventory reduction event means you get a rock bottom, half-off price of $13/unit on our most popular Smooth Firestop Sleeve System. You save $13 a unit! Plus, FREE SHIPPING anywhere in the USA.

HOW TO ORDER: Total price for a case of 75 sleeve systems is $975. (Regular price= $1950/case). Limit 10 cases per transaction online. Click to order and use Coupon code ’50offshipfree’ at checkout. Important: To get free shipping on this product, do not combine with other products in the same order. Or, if you prefer, call the factory at 251-960-5018 and ask for Mike.

Description

Re-enterable Fire Stop Solution – UL Classified for up to 2 hours horizontally – Multi-Cable Transit System – System UL tested for F, T and L ratings!

Don’t be fooled by similar looking products of lower quality. This is the original UNIQUE Smooth Firestop Sleeve System complete with everything you need for installation, including our UNIQUE Intumescent Putty.

The specifications on this special length sleeve are exactly the same as our original 12″ long SF-1, except:

  • The sleeve length is 18″ rather than the standard 12″. Perfect for commercial/industrial new horizontal installations.
  • The sleeve is galvanized like the photo instead of our signature red powder-coat finish.

Designed to firestop cables and wires through fire- and smoke-rated walls, the wall will be firestopped and smoke sealed 100% of the time. Acts like a “roller” in the firewall allowing the installer to pull cables through unattended even at a 45 degree angle. A real time saver! Our most economical product, this sleeve system makes firewall penetrations neat, clean, and code-compliant.

Note: These systems are limited to 2 hour rated horizontal installations. For higher ratings or vertical installations, see our Threaded Firestop Sleeve System.

System Contents:

1 – 18″ EMT sleeve galvanized- (Manufactured from ASTM Electrical Metallic Tubing (EMT) to UL1479 standards.)
2 – large washers
2 – sliding lock couplings
2 – plenum rated bushings
2 – documentation/warning labels- (A pair of highly visible documentation/warning labels records cable count, size, installer’s info and the applicable UL Listing # and are used for digital documentation of your installed system.)
1 – UNIQUE Intumescent Putty

All UNIQUE firestop sleeve systems include enough UNIQUE firestopping Intumescent Putty for a minimum of 25% and  a maximum of 48% cable load. Order additional Intumescent Putty Fill Kits here.

Cable Load Chart

Click on image for a larger view.

smooth-sleeve-cable-load

Our systems come with enough UNIQUE putty for a minimum 25% and maximum 48% cable load.

load formula

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Installation Pictorial

sp-install1(100sq) This UNIQUE Smooth Firestop Sleeve System consists of:  An 18 inch length of EMT,  (2) large washers,  (2) sliding compression couplings,  (2) plenum rated bushings,  a pair of documentation/warning labels and a package of UNIQUE Intumescent Putty.
sp-install2(100sq) You should use a drill with a level. This will make your Sleeve System install nice and straight!
sp-install3(100sq) A 6 inch bit extension for your hole bits works very well. Be wary of what might be in the walls.
sp-install4(100sq) You might use one of the washers to mark your hole. Now drill your perfectly straight hole.
sp-install5(100sq) Adjust the hardware to allow for equal protrusion on both sides of the wall.  Insert the first half of the System in the hole you made.  There is no need for any caulk between the sleeve and the wall (behind the washers).  Go to the other side …
sp-install6(100sq) On the other side of the wall, install the washer, sliding compression coupling and bushing.  While holding the sleeve firmly in the wall, tighten the set screw on the sliding compression coupling.  Now you may use the sleeve system as if it were a roller in the firewall, allowing you to pull cables ‘unattended ‘.  This is a real time saver!
sp-install7(100sq) Tear the intumescent putty supplied with the system in half.  You will need to apply an inch thickness to each end.  If you do not have enough putty, you may purchase an extra Fill Kit.  It is an 18 cubic inch stick of UNIQUE Intumescent Putty.
sp-install8(100sq) When the cables reach their destination, install an inch thickness of the supplied UNIQUE Intumescent Putty.  Alpha numerically ID your installation.  Be sure to fill out and apply the labels. Take a picture of your installed System!

Assembly Instructions

Determine the System size and penetration point that you want to make in the firewall.  See the Cable Load Chart.

Up to 48 % of the aggregate cross-sectional area of the Sleeve System may be filled with cables in walls rated up to 2 hours. The remaining void should be filled with UNIQUE Intumescent Putty, supplied with the Sleeve System.

Find the applicable UL Listing for your Installation.  Look carefully at the illustration ‘Calculating % Fill’.

Disassemble the System and remove one end’s bushing by loosening the sliding lock couplings and using the hardware to ‘slide hammer’ the bushing off of one end of the Sleeve. This will prevent damage to the bushing. Be careful when installing the bushing after the Sleeve System is in the wall- it can shatter!

If you are installing more than a few Sleeve Systems, for sheet rock, you might consider a cordless drill (with level). Use the proper sized hole saws on 6 inch bit extensions.  See the cable load charts for Systems outside diameter (O.D.). Block walls should be core drilled.

After the penetration is made, reassemble one side and slide the Smooth Firestop Sleeve through the wall, seating the first washer against the wall.  Adjust the sliding set screw lock to equalize the length of protrusion.  As long as the hole is the same as the O.D. of the sleeve, no caulk is required behind the washers.

Go to the other side of the firewall, slide the washer over the system, and seat it against the wall.  Slide the second sliding lock coupling up to the second washer. While pulling on the System, push the second lock coupling against the washer/wall until it seats.  Lock down the sliding lock couplings and carefully install the plastic bushing on the end.

The Sleeve can now be used to pull your cables through the wall and onto their destination.  UNIQUE Intumescent Putty for the sealing of our Systems is packaged with the Sleeve.  For the Fill Void or Cavity Material, refer to the applicable UL Listing.

If you have questions, call us at 251-960-5018 and ask for Tech Support.

Drawings & Specs

Architects, Engineers, and Certified Installers can download and use these drawings to specify our systems in their construction projects.

Drawings in Adobe Acrobat (PDF) format:

AutoCAD drawings (DWG), compressed (ZIP) for download:

If you do not have AutoCAD, you can download Autodesk DWG TrueView (free DWG Viewer) to view the drawings.

SDS

Click on each of the links below to access SDS information for this product:

UL Systems